[SOLVED]Read CD-ROM by ATAPI failed....

Question about which tools to use, bugs, the best way to implement a function, etc should go here. Don't forget to see if your question is answered in the wiki first! When in doubt post here.
Post Reply
windows8
Member
Member
Posts: 33
Joined: Sat Feb 23, 2013 3:52 am

[SOLVED]Read CD-ROM by ATAPI failed....

Post by windows8 »

A few days ago,I tried to read data from CD-ROM by ATAPI.
I was not using IRQs,just poll (wait for DRQ set).It's successful!!!
Now I try to wait for IRQ arrives. I failed.

Code: Select all

   requestIRQ(14,&ideIRQPrimary);
   requestIRQ(15,&ideIRQSecondary); 
   /*I had written a timer interrupt,so this code should have no problems.*/

   ideOutb(IDE_PRIMARY  ,IDE_REG_CONTROL,IDE_ENABLE_IRQ);
   ideOutb(IDE_SECONDARY,IDE_REG_CONTROL,IDE_ENABLE_IRQ);

Code: Select all

   const u8 primary = device->primary;
   const u8 master = device->master;
   u8 cmd[12] = {0xa8 /*READ (12).*/,0,0,0,0,0,0,0,0,0,0,0};
      /*SCSI Command.*/

   ideWaitReady(primary);
   ideOutb(primary,IDE_REG_DEV_SEL,master << 4);
   for(int i = 0;i < 4;++i) /*A little delay.*/
     ideInb(primary,IDE_REG_CONTROL);
   ideOutb(primary,IDE_REG_FEATURES,0x0); /*PIO Mode.*/
   ideOutb(primary,IDE_REG_LBA1,(ATAPI_SECTOR_SIZE & 0xff)); 
   ideOutb(primary,IDE_REG_LBA2,((ATAPI_SECTOR_SIZE >> 8)) & 0xff);
   ideOutb(primary,IDE_REG_COMMAND,IDE_CMD_PACKET);

   if(ideWaitInterrupt(device))
      return -1; /*Return if error.*/
/*If I use 'ideWaitDRQ(primary)' instead of 'ideWaitInterrupt(device)',it's successful.*/
/*But if not,ideWaitInterrupt never returns. IRQ never arrivers,why?*/

Code: Select all


/*Do other things.*/

My IRQ handlers:

Code: Select all

static int ideIRQPrimary(IRQRegisters *reg,void *data)
{
   printk("IDE IRQ arrives!\n"); 
   
/*It is a test,I know that IRQ never arrives through it.*/

Code: Select all

/*So this code below never runs.*/
   u8 status = ideInb(IDE_PRIMARY,IDE_REG_STATUS);
   if(!data)
      return 0;
   IDEInterruptWait *wait = (IDEInterruptWait *)data;
   if(wait->primary != IDE_PRIMARY)
      return 0;
   wait->status = status;
   wakeUpTask(wait->task);
   return 0;
}
The wiki says "Then wait for another IRQ. You cannot poll." (http://wiki.osdev.org/ATAPI)
But I poll successfully and fail to wait for an IRQ.What's the reason???
Thanks.
Last edited by windows8 on Sun Dec 22, 2013 3:36 am, edited 1 time in total.
windows8
Member
Member
Posts: 33
Joined: Sat Feb 23, 2013 3:52 am

Re: Read CD-ROM by ATAPI failed....

Post by windows8 »

Solved!!
The wiki may make a mistake.

When we read ATAPI device,we should do this:
1.Set some registers:
a. device => master << 4
b. control => 0 (Enable Interrupts) or 2 (Disable Interrupts)
c. lba2 << 8 + lba1 => ATAPI Sector Size (2048)
d. features => 0 (PIO)
2.Send a command: PACKET COMMAND (0xa0)
3.Now poll for DRQ set,can not wait for irq!!!! (QEMU VirtualBox didn't make any irqs!!)
The wiki says "Wait for an IRQ, or poll for BSY to clear and DRQ to set."

4.Send a SCSI command to data register.
5.Now wait for irqs or poll.
The wiki says "Then wait for another IRQ. You cannot poll."

6.Read data from data register.
7.Wait for another irq. (If control register is 2,just do nothing.)

Am I right? Why does the wiki say so?
dansmahajan
Member
Member
Posts: 62
Joined: Mon Jan 07, 2013 10:38 am

Re: Read CD-ROM by ATAPI failed....

Post by dansmahajan »

Actually irq fires,do following things to be sure
1. check whether interrupt are enabled
2. print a statement whenever a interrupt fire ie in your interrupt handler(common to all interrupts) function
windows8
Member
Member
Posts: 33
Joined: Sat Feb 23, 2013 3:52 am

Re: Read CD-ROM by ATAPI failed....

Post by windows8 »

dansmahajan wrote:Actually irq fires,do following things to be sure
1. check whether interrupt are enabled
2. print a statement whenever a interrupt fire ie in your interrupt handler(common to all interrupts) function
Thanks for your reply.I have solved it.
See my reply above.
Post Reply