The Place to Start for Operating System Developers
It is currently Thu Nov 26, 2020 7:10 am

All times are UTC - 6 hours

Post new topic Reply to topic  [ 3 posts ] 
Author Message
 Post subject: ARM/QEMU PL110
PostPosted: Sat Apr 13, 2019 11:38 pm 

Joined: Sat Apr 13, 2019 10:55 pm
Posts: 4
I'm attempting to demo some low level graphics stuff for ARM. So I'm targeting what is supposed to be easy graphics, PL110. But so far all it does is sit black. I've attempted to follow the osdev wiki but it doesn't seem to work either. Chief problem is I'm pretty sure qemu changed it's memory map since that was written. I played around with the code a little but didn't see much. So here's mine:

#include "stdint.h"

#include "uart.h"
#include "utility.h"

volatile unsigned char * const CLCD = (unsigned char *) 0x10120000;


void PrintClcdPerifId()
   char buffer[5];
   DEBUG_PRINT("ClcdPerifId: ");
   DEBUG_PRINT(CharToHex(*(CLCD + CLCDPERIPHID0), buffer));
   DEBUG_PRINT(CharToHex(*(CLCD + CLCDPERIPHID1), buffer));
   DEBUG_PRINT(CharToHex(*(CLCD + CLCDPERIPHID2), buffer));
   DEBUG_PRINT(CharToHex(*(CLCD + CLCDPERIPHID3), buffer));

#define CLCDPCELLID0 0xFF0
#define CLCDPCELLID1 0xFF4
#define CLCDPCELLID2 0xFF8

void PrintClcdCellId()
   char buffer[5];
   DEBUG_PRINT("ClcdCellId: ");
   DEBUG_PRINT(CharToHex(*(CLCD + CLCDPCELLID0), buffer));
   DEBUG_PRINT(CharToHex(*(CLCD + CLCDPCELLID1), buffer));
   DEBUG_PRINT(CharToHex(*(CLCD + CLCDPCELLID2), buffer));
   DEBUG_PRINT(CharToHex(*(CLCD + CLCDPCELLID3), buffer));

#define LCDTIMING0    0x0
#define LCDTIMING1    0x4
#define LCDTIMING2    0x8
#define LCDTIMING3    0xC

#define VGATIM0      0x3F1F3F9C
#define VGATIM1      0x090B616F
#define VGATIM2      0x067F1800

#define QVGATIM0   0x0505054C
#define QVGATIM1   0x050514EF
#define QVGATIM2   0x05EF1800

void SetClcdTiming()
   uint32_t volatile *pRegister;
   DEBUG_PRINT("Setting CLCD timing registers\n");
   pRegister = (uint32_t*) CLCD + LCDTIMING0;
   *pRegister = VGATIM0;
   pRegister = (uint32_t*) CLCD + LCDTIMING1;
   *pRegister = VGATIM1;
   pRegister = (uint32_t*) CLCD + LCDTIMING2;
   *pRegister = VGATIM2;

#define LCDCONTROL    0x1C

#define TFT24BITEN   0x182B

void SetClcdControl()
   uint32_t volatile *pRegister;
   DEBUG_PRINT("Set CLCD Control Registers\n");
   pRegister = (uint32_t *) CLCD + LCDCONTROL;
   *pRegister = TFT24BITEN;

#define LCDUPBASE 0x10

void SetClcdBuffer(uint32_t frameBufferLoc)
   uint32_t volatile *pRegister;
   DEBUG_PRINT("Set CLCD Frame Buffer\n");
   pRegister = (uint32_t *) CLCD + LCDUPBASE;
   *pRegister = frameBufferLoc;

#define DEFAULT_BUFFER_LOC 0x200000

void InitClcd()
   uint16_t volatile *fb;
   fb = (uint16_t *) DEFAULT_BUFFER_LOC;
   int x;
   for (x = 0; x < (640 * 480) - 10; ++x)
      fb[x] = 0x1f << (5 + 6) | 0xf << 5;
   DEBUG_PRINT("InitCLCD Done\n");

DEBUG_PRINT is a UART print which is fed to stdio. I run qemu using
qemu-system-arm -M versatilepb -m 256M -serial stdio -kernel QG.elf
and the output falls all the way to done so I know it should be doing something but the graphical window stays black.

Begin System Manager
ClcdPerifId: 10 11 04 00
ClcdCellId: 0D F0 05 B1
Setting CLCD timing registers
Set CLCD Frame Buffer
Set CLCD Control Registers
InitCLCD Done

Thanks for any help.

 Post subject: Re: ARM/QEMU PL110
PostPosted: Sun Apr 14, 2019 12:19 am 

Joined: Sat Jul 02, 2016 7:02 am
Posts: 145
There might be more differences than I list here, but if versatilepb is the board chosen, then it "has a variant halfway between PL110 and PL111" (according to Linux).

It means that the offsets of the control register and the interrupt-mask register are to be swapped.

Specifically, LCDCONTROL in your case is at 0x18 (and not at 0x1c as your code defines; 0x1c in your code ought to be interrupt-enable mask).

 Post subject: Re: ARM/QEMU PL110
PostPosted: Sun Apr 14, 2019 9:29 am 

Joined: Sat Apr 13, 2019 10:55 pm
Posts: 4
Nearly as soon as I posted this I found someone using 0x18 as CONTROL. Tried it and it worked. :roll:

Thanks for the rhyme to the reason because I was very weirded out by that change.

Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 3 posts ] 

All times are UTC - 6 hours

Who is online

Users browsing this forum: 8infy, qookie and 16 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group