OSDev.org
https://forum.osdev.org/

QEMU: rtl8139 not filling rx buffer
https://forum.osdev.org/viewtopic.php?f=1&t=33423
Page 1 of 1

Author:  Artyom [ Wed Jan 09, 2019 6:01 am ]
Post subject:  QEMU: rtl8139 not filling rx buffer

Hi! I'm having a problem with my rtl8139 driver. I receive interrupts from it when data packets come in, but for some reason the rx buffer that it is suppose to fill with incoming packets doesn't fill.

Here is my code:
Code:
#define RX_BUF_LEN 8192 + 16 + 1500
#define RX_READ_POINTER_MASK (~3)
uint nic_base;
uint rx_buffer;
uint cpptr;

extern void set_idt_handler(int i, void (*handler));
extern void nic_irq();

void rtl8139_handler()
{
   int status = inw(nic_base + 0x3e);

   if(status & (1 << 0))
   {
      printf("\nrtl8139: debug: received packet");

      u16* pointer = (u16*)(rx_buffer + cpptr);  // packet pointer
      u16  pLen = *(t + 1);                                 // packet len

                // data pointer
      pointer = pointer + 2;
               
      void * packet_data = malloc(pLen);   
      memcpy(packet_data, pointer, pLen);
      mem_dump(packet_data, pLen, 15);

      printf("\n packet len %d", pLen);
      
      cpptr = (cpptr + packet_length + 4 + 3) & RX_READ_POINTER_MASK;

      if (cpptr > RX_BUF_LEN)
         cpptr -= RX_BUF_LEN;

      outw(nic_base + 0x38, cpptr - 0x10);
   }
   outw(nic_base + 0x3E, 0x5);
}

void rtl8139_init()
{
   uint8_t bus;
   uint8_t slot;
   uint8_t func;

   PCIFindDevice2(&bus, &slot, &func, 0x8139, 0x10EC);
   
   if(bus      == 0xFF) return;
   if(slot      == 0xFF) return;
   if(func     == 0xFF) return;
   
   PciBar bar;
   PciGetBar(&bar, PCI_MAKE_ID(bus, slot, func), 0);

   uint32_t nic_addr = bar.u.port;

   printf("\nrtl8139: driver started");

   // Enable PCI Bus Mastering for NIC
   unsigned short cfg = PciRead16(PCI_MAKE_ID(bus, slot, func), 4);
   PciWrite16(PCI_MAKE_ID(bus, slot, func), 4, cfg | 2);

   // turn on
   outb(bar.u.port + 0x52, 0);
   printf("\nrtl8139: turned on");

   // Send reset command to NIC
   printf("\nrtl8139: reseting card");
   outb(bar.u.port + 0x37, 0x10);

   // Wait.....
   while(inb(bar.u.port + 0x37) & 0x10){}

   // Allocate rx_buffer
   rx_buffer = malloc(RX_BUF_LEN);

   // set RX-buffer and interrupts
   outl(bar.u.port + 0x30, (uint)rx_buffer);

        // set IMR + ISR
   outw(bar.u.port + 0x3C, 0x0005);
        // Configuring receive buffer (RCR)
   outd(bar.u.port + 0x44, 0xf | (1 << 7));
        // Enable Receive and Transmitter
   outb(bar.u.port + 0x37, 0x0C);

      
   uint8_t irq = (uint8_t)PCIGetIRQ(bus, slot, func);
   __asm("cli");
   set_idt_handler(irq+32, &nic_irq);
   __asm("sti");

   nic_base = bar.u.port;
}


Any help is much appreciated, thanks!

Author:  GhelloWorld [ Thu Jan 10, 2019 7:43 am ]
Post subject:  Re: QEMU: rtl8139 not filling rx buffer

Hello Artyom,

I have also had some problems with this particular card, luckily those where solved in this post: viewtopic.php?f=1&t=33157. One the biggest problems I had was that my buffer was not aligned, you should really do that.
One other thing to make debugging this card easier is to recompile qemu with DEBUG_RTL8139 Enabled, you can find this line in qemu/hw/rtl8139.c

Greetings,

Remco

Author:  Artyom [ Thu Jan 10, 2019 8:59 am ]
Post subject:  Re: QEMU: rtl8139 not filling rx buffer

GhelloWorld wrote:
Hello Artyom,

I have also had some problems with this particular card, luckily those where solved in this post: viewtopic.php?f=1&t=33157. One the biggest problems I had was that my buffer was not aligned, you should really do that.
One other thing to make debugging this card easier is to recompile qemu with DEBUG_RTL8139 Enabled, you can find this line in qemu/hw/rtl8139.c

Greetings,

Remco


Thank you so much for your help! It works!

Page 1 of 1 All times are UTC - 6 hours
Powered by phpBB © 2000, 2002, 2005, 2007 phpBB Group
http://www.phpbb.com/